¡Ü½Å±Ô°³¹ßµÈ °í¼º´É DSP¸¦ žÀçÇÑ ÇÁ·Î¼¼¼¿Í ÃÖ÷´Ü ÆÄ¿ö ¾ÚÇÁ ±â¼úÀÌ ¿õÇÕµÈ ÆÄ¿ö ¾ÚÇÁ ³»Àå TD ÄÁÆ®·Ñ·¯ |
¡ÜNXAMPÀÇ ÇÁ·Î¼¼¼ ºÎºÐ¿¡´Â NX242¸¦ »óȸÇÏ´Â DSP 󸮴ɷÂÀÌ ½ÇÀåµÇ¾î ¸ðµç NEXO½ºÇÇÄ¿¿¡ ´ëÀÀ |
¡Ü¾ÚÇÁÃâ·ÂÀÇ Àü¾Ð, Àü·ù µîÀ» °¨½ÃÇÏ¿© ½Ã½ºÅÛ Àüü¸¦ ¾ÈÀüÇÏ°Ô ±¸µ¿½ÃÅ°¸é¼ ½ºÇÇÄ¿ÀÇ ´É·ÂÀ» ÃÖ´ëÇÑÀ¸·Î ÀÎÃâ |
¡Ü¾ÚÇÁ ³»ºÎÀÇ °¢Ã¤³Î¸¶´Ù µ¶¸³µÈ Àü¿ø°ø±ÞÀ¯´ÏÆ®¸¦ Á¦°øÇÏ¿© ¾ÐµµÀûÀ¸·Î ¾ÈÁ¤µÈ µ¿ÀÛ°ú ³ôÀº ½Å·Ú¼º |
POWER SPECIFICATIONS |
|
NXAMP4X1 |
NXAMP4X4 |
Number of amplifiers channels |
4x channels, 2 by 2 bridgeable |
4x channels, 2 by 2 bridgeable |
Max. output voltage (no load) |
4 x 105Volts |
4 x 200Volts |
Max. output power (8§Ù) |
4 x 600W |
4 x 1900W |
Max. output power (4§Ù) |
4 x 900W |
4 x 3300W |
Max. output power (2§Ù) |
4 x 1300W |
4 x 4000W |
Power consumption (Standby) |
10W |
20W |
Power consumption (Idle) |
100W |
150W |
Power consumption (1/8 Power) |
1100W |
3000W |
COMMON NXAMP SPECIFICATIONS FROM ANALOG IN TO POWER OUT |
Analog Inputs channels |
4x channels, analogue inputs on XLR 3 with a second XLR 3 for linking |
Frequency response |
¡¾0.5dB from 10Hz to 20KHz |
Input Impedance |
20K§Ù |
Max Input Level |
+28dBu |
Dynamic Range |
All Channels = 105dB unweighted |
THD + Noise |
Typical 0.1% flat setup |
Latency time |
500us on a flat setup |
Power Supply |
Dedicated version for 100 ~ 120Volts or 220 ~ 240Volts |
COMMON NXAMP FEATURES |
Audio Inputs |
• 4x balanced analogue inputs on XLR3 with a second XLR3 for linking, using 24bit converters. |
|
• 4x digital inputs via the optional network card slot at the back. |
Power Outputs |
4x Speakon outputs using internal power relay for automatic output assignment regarding setup. |
RS232 port |
Allow firmware upgrade for software improvement and new cabinet setups. |
GPIO port |
5x Global Purpose Inputs and 8x Global Purpose Outputs for simple remote control and monitoring. |
Processing |
Two DSPs, 24bit data with 48bit accumulator. 700MIPS. |
Dimensions & Weight |
NXAMP4x1: 3U 19¡± Rack - 457 mm (18¡±) Depth - 16.5kg (33lbs) net |
|
NXAMP4x4: 4U 19¡± Rack - 457 mm (18¡±) Depth - 24.5kg (49lbs) net |
NXAMP USER CONTROLS |
System Set-up |
Within the selected range, if possible, allows cabinets to be set for passive or active mode, wideband |
|
or crossover mode, choose among available crossover point, cardioid or supercardioid mode. |
Protection |
Multiple Peak Limiters fitted for both selected cabinet and amplifier. Multiple Acceleration, |
|
Displacement and Temperature protections on every channel. Inter-channel regulation. |
Delay |
Up to 150m (330 ft.) of delay in 10cm (.4in ) steps |
Array EQ |
LF or HF shelving filters to compensate ground or stacking effects, ¡¾6dB, frequency factory tuned. |